- #VAG K CAN COMMANDER 1.4 TORRENT UPDATE#
- #VAG K CAN COMMANDER 1.4 TORRENT DRIVER#
- #VAG K CAN COMMANDER 1.4 TORRENT MANUAL#
- #VAG K CAN COMMANDER 1.4 TORRENT SOFTWARE#
#VAG K CAN COMMANDER 1.4 TORRENT SOFTWARE#
*Now the next important step is to connect the Vag Commander software with supplied OBD2 cable to your car and connect to instrument cluster Lens taken off for scratch removal and cleaningĪll cleaned up, this cluster came from a 63k mile RS6 Here are both clusters next to each other for comparison, they are physically the same on the outside which makes fitment a breeze. After doing a little research I found that it is possible to properly swap the RS6 cluster into my A6 with the proper tools and information even though I have Immo 3.Īfter receiving the donor RS6 cluster I took it apart for a general cleaning and inspecting for any obvious electrical damage that would cause an issue down the line. ***Make sure you have a constant 12v power supply throughout the process, this is very important***Īfter 7 years of owning my Audi I finally pulled the trigger on a nicely used instrument cluster from a 2003 RS6.
#VAG K CAN COMMANDER 1.4 TORRENT DRIVER#
Phillips screw driver for removing two screws that hold cluster in There is a small chance you can do permanent damage to your cluster if proper procedure is not followed, and finally these instructions and info are not intended for any illegal use. Key learning function (without need of security access code/login)įor Audi A4 after 2000 - petrol engines >= 1.DISCLAIMER: These are instructions for replacing an instrument cluster in an Audi that uses the Immobilizer security feature.
#VAG K CAN COMMANDER 1.4 TORRENT UPDATE#
Porsche 911 (996/997), Porsche Boxster, Porsche Cayman, Porsche Cayenne - Read EEPROM via OBDIIīOSCH VAG-EDC15x, VAG-ME7.1.1, VAG-ME7.1, VAG-ME7.5, VAG-Cartronic ME7.8, MED9x - FSI, EDC16x - Read flashmemory by OBDII (near update programming of flash memories with function for resetting of reflashing counter) (extracting security code, odometer correction, enable disable immobilizer and so on) Read/Write EEPROM of Engine Control UnitsīOSCH VAG-EDC15x, VAG-ME7.1.1, VAG-ME7.1, VAG-ME7.5, VAG-Cartronic ME7.8. K-line UPDATE - Odometer correct / Security code reading / Read/Write EEPROMįor Seat Ibiza VDO after 1999 (K) (MY2007 covered)įor VW Polo VDO/Motometer (K) (MY2007 covered) Security code reading (CAN) / Read/Write EEPROM memory Memories Special function - Crash data clear in airbag units MED951, MED751 (with next update will be possible programming of flash Special function - Reading flash memories EDC16x, EDC15x, ME7x, Special function - Custom memory reading from different units like ECUs, EZS-Kessy and s.o. Special function - Key learning Porsche CAYENNE (not needed security code) K+CAN. Special function - Key learning buttons for easy usage (not needed security code). Special function - Read/Write EEPROM of Engine Control Units BOSCH VAG-EDC15x, VAG-ME7.1.1, VAG-Cartronic ME7.8,Porsche. Special function - VAG MMI TV Activation. Special function - read/write EEPROM from instrument cluster/immobilizer. Special function - read/program immobilizer data.
Special function - read Security Access Code/Login WFS. Special function - odometer correction in instrument clusters and EDC15x. Most of popular diagnostic requests ¡¡?¬C identifications, coding, adaptations, DTCs and s.o.
Functions are underĪllows managing of brand new units (and immobilizer units) where isĪllowed programming of PIN, SKC, BGW, MAC. Remaining diagnostic tools always standard diagnostic session 0x89.īroadcast diagnostic request ¡¡?¬C disable normal communication,Ĭlear DTCs, Logistic (transport) mode.
#VAG K CAN COMMANDER 1.4 TORRENT MANUAL#
Manual definition of running diagnostic session ¡¡?¬C not like Some new units untouchable for remaining diagnostic tools. This can allow of user to investigate and diagnosis This cable functions with v3.0 and v3.6 of Abritus software.ĭiagnostic via CAN and Special functions via K-line.Ĭovers all electronic control units in vehicles (diagnostic addressesįrom 0x01 to 0x80). VAG K + CAN Commander v3.6 offers many features for For Audi / For Volkswagen / For Seat / For Skoda / Porsche vehicles.
0 kommentar(er)
